ST-10

Reference class power amplifier

The ST-10 amplifier is for listeners who require a reference-class amplifier at a somewhat lesser power rating of 2 x 150W (8 Ohm). NuPrime’s sonic character stands well apart from – and indeed above – the soft, cushy sound we often associate with most tubed amplification and the dry, clinically edgy sound we often associate with solid-state and switching technology. Rarely does an amp achieve an ideal balance of richly textured timbres and harmonics, bottom-end authority, startling dynamics, exquisite low-level detail, and a fully revealed, fully dimensional sound stage against a backdrop of mile-deep silence.

EUR 1,795.00

Category:

 

Guides:

--> Amp Comparison & Sonic Characteristic
--> Amp Design & NuPrime's Advantages

The fourth generation (V4 amplifier module) of this patented amplifier design outperforms its predecessor in several aspects:

– It lowers the noise floor by an astounding 20dB and elevates the output stage to 85% efficiency.
– Shortened circuit pathways result in a 20% improvement in through-put.
– Improved reliability in no-load condition and short circuit protection.
– Increased output current drive capability for low impedance speakers.
– Increased switching frequency to 600 KHz and an improved musical sampling rate.
– Improved S/N ratio and dynamic range.
– New linear power supply with a high-efficiency toroidal transformer. Reduced high-frequency noise and strengthened low-frequency performance.
– Signal path avoids cross-linking capacitors, thus achieving a frequency response at DC level for pure musical enjoyment.
– Enhanced even-order harmonic (H2) circuitry resembling the most attractive features of tubed-amp sound without its drawbacks and limitations.

The NuPrime Sound

– Vast soundstage
– Wide, lightning-fast dynamics
– Ultra-low distortion and noise
– Music emerges from a pristine background, with delicate details and nuances intact

  • Inputs:
    • RCA: Un-Balanced input x 1
    • XLR: Balanced input x 1
  • Outputs:
    • Stereo Speaker Out x 1
  • Power Output: 150W x 2 at 8 Ohms; 150W x 2 @ 4 Ohms
  • Gain: X 28 (RCA); X 52 (XLR)
  • Input Impedance: 23.5k Ohms
  • 12V trigger input. It can use any standard male to male 3.5mm (3-pin type) cable.
  • Sensitivity: 0.89 V to rated power
  • THD+N: 0.01%
  • Frequency Response: 0 Hz to 50kHz (-3dB)
  • S/N Ratio: 91dB @ 10W
  • Dimensions: 59 mm H x 215.4 mm W x 394 mm D
  • Weight: 7 kg

ST-10 is a phase inverting amp. If you are certain that the +/- (usually the red/white connectors) phase of your inputs are non inverting, then you should reverse the +/- inputs for each channel on ST-10.  All other NuPrime amps were designed as non-inverting amp.  If you have no idea what this is all about, don’t bother with making any adjustment.

   

 

Review of ST-10 in AudioCircle

Review of ST-10 in AudioCircle

– ZAPHOD2012, audiocircle.com

“…I have Audience 2+2 in a stereo system in the bedroom, they have been powered by Cary Audio and Parasound multi channels. Due to the weight and only stereo need i sold the Cary and Parasound for the Nuprime ST-10. I was cautious as i have hated my previous experiments with class d amps such as rotel, pioneer and wyred4sound, all cold and lifeless, boring and flat. The ST-10 was a revelation, sweet, very detailed, tight, extended and bouncy, it had life and was a joyful match with the 2+2’s, I cannot remember a more enjoyable sound in 30 years, especially for the money, and the mids are incredible…

…In my main system i needed to replace my hernia weighted Cary 7 channel, so with my positive experience with the ST-10 I plumped for the MCH-K38 at half the weight of the Cary and hoping it would come close to the exceptional ST-10. The MCH-K38 will be used in a 5.1 system driving Audience 4+4’s when they arrive from the factory. In 5.1 mode the first 4 channels will be bridged and that is how i compared it to the ST-10, not only did it equal the ST-10 but in bridged mode bettered it. Same family signature but just with a more effortless control, more open, less restrained and detailed, I am extremely surprised and very happy, what a combination made in heaven, the Audience and the Nuprime ….rock on ….”


NuPrime DAC-10H DAC/Pre and ST-10 Power Amplifier

NuPrime DAC-10H DAC/Pre and ST-10 Power Amplifier

– Steven Stone, theabsolutesound.com

DAC-10H
“……Within their product categories the DAC-10H DAC/preamp and ST-10 basic power amplifier are priced at the lower mid-level, yet they both deliver a level of performance that could be considered exemplary regardless of their cost. The DAC-10H has the capabilities, sound, and feature set that should keep it current for a number of years, while the ST-10 produces a level of sound quality that unless you absolutely must have more power output capabilities, will make “upgrading” to anything but a far pricier and more powerful amplifier more of a sideways proposition than an upward one…
…As it is a relatively new firm, NuPrime has yet to develop the reputation and visibility of more venerable audio companies. But given the quality of its first three products, the IDA-16, DAC-10H, and ST-10, it’s hard not to predict that NuPrime will be a force to be reckoned with now and in the future…”

ST-10
“…over the years I’ve reviewed and used plenty of digital power amplifiers from Bel Canto, Wyred4Sound, April Music, and others, and I appreciate what a well-designed model can bring to a system. And it happens that the ST-10 is the best digital power amplifier I’ve heard to date…

…Within their product categories the DAC-10H DAC/preamp and ST-10 basic power amplifier are priced at the lower mid-level, yet they both deliver a level of performance that could be considered exemplary regardless of their cost… “


NuPrime ST-10M with Magnepan 1.7i

NuPrime ST-10M with Magnepan 1.7i

-By Jan A., audiocircle.com

“…ST10M is a reference level amplifier, just like advertised, in performance at least equal in many respects to the equipment that is multiple of their price level, which is saying something about NuPrime engineering abilities….”


NuPrime DAC-10, ST-10 and Totem Rainmaker speakers

NuPrime DAC-10, ST-10 and Totem Rainmaker speakers

– By RafaPolit, audiocircle.com

“…
For the first time I understand what “sound stage” means. Sound comes from everywhere, not just from the speakers. Each voice and instrument has its own position, really an eye opener for me!
It is a powerful combo, so much so that if you a not careful, you can blow out your speakers.

The clarity of the sound is remarkable if the source has that quality…”


ST-10M with Legacy Helix

ST-10M with Legacy Helix

– By Brad from Canada

“…They sounded pretty impressive right out of the box, but have improved greatly over the last 3 weeks. It would be a huge understatement to say that I’m very impressed with their performance. The following are my observations on sound quality in no particular order: Large holographic soundstage, 3D imaging, completely black background, very neutral and highly resolving, tight defined bass, superb mid-range (vocals are awesome), rich tone, smooth and dynamic. Excellent performance from top to bottom, very musical and engaging (toe tapping goodness!) I’ve been in this hobby for approx. 30 years, and at no time have I come across the price / performance value that NuPrime offers, it really is unbelievable. These amps are the real deal, and I will be keeping them…”


AudioCircle.com ST-10 discussion

c Expand All C Collapse All

Amp & Preamp (3)

In some applications, the speaker outputs from the power amplifier are used as source signals for devices such as REL sub woofer. For such application, usually the receiving devices should have DC offset blocking capability because some amplifier by design has floating ground (DC offset) on the speaker outputs.

The following models have no DC offset on the amplifier speaker outputs and the negative terminal is also the ground:
NuPrime STA-9, MCH-K38, IDA-6, IDA-16, STA-9X, AMG STA

The following models’ speaker outputs can not be connected directly to sub woofer input:
NuPrime Reference 20, ST-10, IDA-8, ST-10M, Evolution One, Evolution Two, Evolution STA, AMG One, MCX-1,2,3,4

REL has provided instructions for connecting Class-D amp with floating speaker outputs to their sub woofers, please contact REL. All currently shipping REL sub woofers can be connected directly to any Nuprime amps.

IDA-8 is an extremely popular and award winning integrated amp. New users are welcome to read this long topic on audiocircle.com: http://www.audiocircle.com/index.php?topic=134697.0

When a device has a 12V trigger input, it is designed to be turned on when a 12V is detected. You can use any standard male to male 3.5mm (3-pin type) cable.
https://components101.com/connectors/35mm-audio-jack

The Tip section is +12V, the bottom Sleeve section is GND, and the middle Ring section is not used. Nuprime’s trigger design uses 3.5mm stereo cable pin 1 and pin 3. A mono trigger cable shorts pin 2 and pin 3, it can be used to connect the Nuprime device to another device’s trigger that only uses a mono cable.

ST-10 Manual

ST-10

EUR 1,795.00

Reference class power amplifier

The ST-10 amplifier is for listeners who require a reference-class amplifier at a somewhat lesser power rating of 2 x 150W (8 Ohm). NuPrime’s sonic character stands well apart from – and indeed above – the soft, cushy sound we often associate with most tubed amplification and the dry, clinically edgy sound we often associate with solid-state and switching technology. Rarely does an amp achieve an ideal balance of richly textured timbres and harmonics, bottom-end authority, startling dynamics, exquisite low-level detail, and a fully revealed, fully dimensional sound stage against a backdrop of mile-deep silence.

Category:

 

Guides:

--> Amp Comparison & Sonic Characteristic
--> Amp Design & NuPrime's Advantages

The fourth generation (V4 amplifier module) of this patented amplifier design outperforms its predecessor in several aspects:

– It lowers the noise floor by an astounding 20dB and elevates the output stage to 85% efficiency.
– Shortened circuit pathways result in a 20% improvement in through-put.
– Improved reliability in no-load condition and short circuit protection.
– Increased output current drive capability for low impedance speakers.
– Increased switching frequency to 600 KHz and an improved musical sampling rate.
– Improved S/N ratio and dynamic range.
– New linear power supply with a high-efficiency toroidal transformer. Reduced high-frequency noise and strengthened low-frequency performance.
– Signal path avoids cross-linking capacitors, thus achieving a frequency response at DC level for pure musical enjoyment.
– Enhanced even-order harmonic (H2) circuitry resembling the most attractive features of tubed-amp sound without its drawbacks and limitations.

The NuPrime Sound

– Vast soundstage
– Wide, lightning-fast dynamics
– Ultra-low distortion and noise
– Music emerges from a pristine background, with delicate details and nuances intact

  • Inputs:
    • RCA: Un-Balanced input x 1
    • XLR: Balanced input x 1
  • Outputs:
    • Stereo Speaker Out x 1
  • Power Output: 150W x 2 at 8 Ohms; 150W x 2 @ 4 Ohms
  • Gain: X 28 (RCA); X 52 (XLR)
  • Input Impedance: 23.5k Ohms
  • 12V trigger input. It can use any standard male to male 3.5mm (3-pin type) cable.
  • Sensitivity: 0.89 V to rated power
  • THD+N: 0.01%
  • Frequency Response: 0 Hz to 50kHz (-3dB)
  • S/N Ratio: 91dB @ 10W
  • Dimensions: 59 mm H x 215.4 mm W x 394 mm D
  • Weight: 7 kg

ST-10 is a phase inverting amp. If you are certain that the +/- (usually the red/white connectors) phase of your inputs are non inverting, then you should reverse the +/- inputs for each channel on ST-10.  All other NuPrime amps were designed as non-inverting amp.  If you have no idea what this is all about, don’t bother with making any adjustment.

   

 

Review of ST-10 in AudioCircle

Review of ST-10 in AudioCircle

– ZAPHOD2012, audiocircle.com

“…I have Audience 2+2 in a stereo system in the bedroom, they have been powered by Cary Audio and Parasound multi channels. Due to the weight and only stereo need i sold the Cary and Parasound for the Nuprime ST-10. I was cautious as i have hated my previous experiments with class d amps such as rotel, pioneer and wyred4sound, all cold and lifeless, boring and flat. The ST-10 was a revelation, sweet, very detailed, tight, extended and bouncy, it had life and was a joyful match with the 2+2’s, I cannot remember a more enjoyable sound in 30 years, especially for the money, and the mids are incredible…

…In my main system i needed to replace my hernia weighted Cary 7 channel, so with my positive experience with the ST-10 I plumped for the MCH-K38 at half the weight of the Cary and hoping it would come close to the exceptional ST-10. The MCH-K38 will be used in a 5.1 system driving Audience 4+4’s when they arrive from the factory. In 5.1 mode the first 4 channels will be bridged and that is how i compared it to the ST-10, not only did it equal the ST-10 but in bridged mode bettered it. Same family signature but just with a more effortless control, more open, less restrained and detailed, I am extremely surprised and very happy, what a combination made in heaven, the Audience and the Nuprime ….rock on ….”


NuPrime DAC-10H DAC/Pre and ST-10 Power Amplifier

NuPrime DAC-10H DAC/Pre and ST-10 Power Amplifier

– Steven Stone, theabsolutesound.com

DAC-10H
“……Within their product categories the DAC-10H DAC/preamp and ST-10 basic power amplifier are priced at the lower mid-level, yet they both deliver a level of performance that could be considered exemplary regardless of their cost. The DAC-10H has the capabilities, sound, and feature set that should keep it current for a number of years, while the ST-10 produces a level of sound quality that unless you absolutely must have more power output capabilities, will make “upgrading” to anything but a far pricier and more powerful amplifier more of a sideways proposition than an upward one…
…As it is a relatively new firm, NuPrime has yet to develop the reputation and visibility of more venerable audio companies. But given the quality of its first three products, the IDA-16, DAC-10H, and ST-10, it’s hard not to predict that NuPrime will be a force to be reckoned with now and in the future…”

ST-10
“…over the years I’ve reviewed and used plenty of digital power amplifiers from Bel Canto, Wyred4Sound, April Music, and others, and I appreciate what a well-designed model can bring to a system. And it happens that the ST-10 is the best digital power amplifier I’ve heard to date…

…Within their product categories the DAC-10H DAC/preamp and ST-10 basic power amplifier are priced at the lower mid-level, yet they both deliver a level of performance that could be considered exemplary regardless of their cost… “


NuPrime ST-10M with Magnepan 1.7i

NuPrime ST-10M with Magnepan 1.7i

-By Jan A., audiocircle.com

“…ST10M is a reference level amplifier, just like advertised, in performance at least equal in many respects to the equipment that is multiple of their price level, which is saying something about NuPrime engineering abilities….”


NuPrime DAC-10, ST-10 and Totem Rainmaker speakers

NuPrime DAC-10, ST-10 and Totem Rainmaker speakers

– By RafaPolit, audiocircle.com

“…
For the first time I understand what “sound stage” means. Sound comes from everywhere, not just from the speakers. Each voice and instrument has its own position, really an eye opener for me!
It is a powerful combo, so much so that if you a not careful, you can blow out your speakers.

The clarity of the sound is remarkable if the source has that quality…”


ST-10M with Legacy Helix

ST-10M with Legacy Helix

– By Brad from Canada

“…They sounded pretty impressive right out of the box, but have improved greatly over the last 3 weeks. It would be a huge understatement to say that I’m very impressed with their performance. The following are my observations on sound quality in no particular order: Large holographic soundstage, 3D imaging, completely black background, very neutral and highly resolving, tight defined bass, superb mid-range (vocals are awesome), rich tone, smooth and dynamic. Excellent performance from top to bottom, very musical and engaging (toe tapping goodness!) I’ve been in this hobby for approx. 30 years, and at no time have I come across the price / performance value that NuPrime offers, it really is unbelievable. These amps are the real deal, and I will be keeping them…”


AudioCircle.com ST-10 discussion

c Expand All C Collapse All

Amp & Preamp (3)

In some applications, the speaker outputs from the power amplifier are used as source signals for devices such as REL sub woofer. For such application, usually the receiving devices should have DC offset blocking capability because some amplifier by design has floating ground (DC offset) on the speaker outputs.

The following models have no DC offset on the amplifier speaker outputs and the negative terminal is also the ground:
NuPrime STA-9, MCH-K38, IDA-6, IDA-16, STA-9X, AMG STA

The following models’ speaker outputs can not be connected directly to sub woofer input:
NuPrime Reference 20, ST-10, IDA-8, ST-10M, Evolution One, Evolution Two, Evolution STA, AMG One, MCX-1,2,3,4

REL has provided instructions for connecting Class-D amp with floating speaker outputs to their sub woofers, please contact REL. All currently shipping REL sub woofers can be connected directly to any Nuprime amps.

IDA-8 is an extremely popular and award winning integrated amp. New users are welcome to read this long topic on audiocircle.com: http://www.audiocircle.com/index.php?topic=134697.0

When a device has a 12V trigger input, it is designed to be turned on when a 12V is detected. You can use any standard male to male 3.5mm (3-pin type) cable.
https://components101.com/connectors/35mm-audio-jack

The Tip section is +12V, the bottom Sleeve section is GND, and the middle Ring section is not used. Nuprime’s trigger design uses 3.5mm stereo cable pin 1 and pin 3. A mono trigger cable shorts pin 2 and pin 3, it can be used to connect the Nuprime device to another device’s trigger that only uses a mono cable.